Please reposition the pinch roller by holding the center of the pinch roller and moving it from the rear end of the machine.
#Papercut driver for mac manual#
Position the Secondary Pinch Roller at the center of media.Įxpert 24 User Manual Note: Always adjust the position with the pinch rollers raised. Position the Primary Pinch Rollers at the right and left sides of media. Expert 24 User Manual Media Loading 2.4.1 Loading the Sheet Media To load the media properly, please follow the below procedures: Step 1 Lift the 2 levers at the back side of cutter to raise pinch rollers ( Figure 2-12.Įxpert 24 User Manual CAUTION! Make sure the Primary and secondary pinch rollers are set to right positions. Please note the outward ring of the holder must put into the grooves of carriage firmly (see Figure 2-10), fasten the case (Figure 2-11).
Expert 24 User Manual Step 4 Insert the blade holder into tool carriage. Make sure that your fingers Outward ring are away from the blade tip. Insert a blade into the bottom of the blade holder and remove the blade by pushing the pin. Expert 24 User Manual 2.3 Blade Installation Figure 2-6 is the illustrator of the blade Adjustment depth knob holder. Position the stand under the plotter, and insert the screws into the holes on the bottom of the plotter but do not tighten them up as shown in Figure 2-4. Expert 24 User Manual Step 5 Remove the cutting plotter from the carton. Stand Beam T-stand Figure 2-2 Step 4 Position both the left Support and right Support perpendicularly to the T-stand and put the screws into the holes and tighten them as shown in Figure 2-3. Gcc Expert 24 Lx DriversĮxpert 24 User Manual Step 3 Place the stand beam upright on the T-stand and put the screws into the holes but do not tighten them at this step. Step 1 Please examine the supplied items in the accessory box of the stand carton before you install: Stand is an optional item for Expert 24, Item List： ： ： ： 1 Left side vertical stand 1 Right side vertical stand. Notice 2 Choosing a proper place before setting up the cutting plotter Before installing your cutting plotter, select a suitable location, which meets the following conditions.
Carefully handle the cutter to prevent any injuries. Notice 1 Make sure the power switch is off before installing the cutting plotter. Installation Precaution Please read below information carefully before you start installation. Power Switch To turn on or off the machine.Įxpert 24 User Manual 2. Expert 24 user manual 1.3.3 The Side Views 【 【 【 【 Figure 1-4】 】 】 】 【 【 【 【 Figure 1-3】 】 】 】 Object Description AC Power Connector To insert the AC power cord. Expert 24 user manual The Appearance (EX-24) 1.3.1 The Front View 【 【 【 【 Figure 1-1】 】 】 】 Object Description Primary Pinch Roller To help hold the media during cutting. If you find any item missing, please consult your local dealer for further assistance.
General Information Package Items The package of Expert 24 contents the items listed below, please check carefully. Trouble Shooting What if Expert 24 cannot Operate? Light Indicators Cutting Quality Problems Appendix A-1 CorelDraw instruction A-2 Expert 24 Specification A-3 Blade Specification. Caution SAFETY PRECAUTIONS! For safety concern, please always hold the cutter firmly from the bottom while moving it.īasic Maintenance Cleaning the cutting Plotter Cleaning the Grid Drum Cleaning the Pinch Rollers 5. Before you use the cutting plotter, please make sure that you have read the safety precautions and instructions below. Expert 24 user manual Important Information Thank you for purchasing the Expert 24 Cutting Plotter. All comments, queries or suggestions concerning this manual please consult with your local dealer. NOTICE GCC reserves the right to modify the information contained in this user manual at any time without prior notice un-authorised modification, copying distribution or display is prohibited. EXPERT 24 CUTTING PLOTTER User Manual Great Computer Corporation © V.10 2013 Dec. Media Width 719 mm (28.3 in.) 1635 mm (64.37”) Acceptable Material Thickness 0.8 mm Cutting Force 350 g Max.
#Papercut driver for mac series#
GCC Expert Vinyl Cutter For additional product information Click Here For additional product information Click Here For additional product information Click Here Expert 24 is the best choice for beginners and provides sign makers with optimum speed, superior quality, solid reliability and unmatched value.Įxpert II Series EX II-24 EX II-24LX EX II-52 EX II-52LX Max. The versatile Expert II Series sets a new benchmark for value, offering high accuracy and reliability at an unbelievably affordable price.
Expert II Series Vinyl Cutter is the best choice for beginners and provides sign makers with optimum speed, superior quality, solid reliability and unmatched value.
0 kommentar(er)
